cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits

A specification sheet can appear straightforward until a buyer has to match it to trench depth, lift capacity, or tight access work. Understanding mini excavator specifications is less about memorizing rated power and more about reading the numbers that constrain the job. In more than ten years of equipment documentation work, I have seen procurement teams shortlist machines on engine output alone, then discover the hydraulic flow or transport width will not handle the application. This article explains which specification lines matter first, how they interact, and what to confirm before a purchase decision.

What Do Mini Excavator Specifications Actually Cover?

A specification sheet for a compact excavator usually separates data into working range, hydraulic performance, and machine dimensions. Working range covers digging depth, reach at ground level, and bucket breakout force. Hydraulic performance covers pump flow, system pressure, and auxiliary circuit capacity. Machine dimensions cover operating weight, ground pressure, tail swing radius, and transport width. Buyers tend to read the headline figure, often operating weight or engine power, and then stop. The more useful approach is to check whether the smaller values match the reach, the planned attachment flow, and the access route.

Working Range Numbers

Digging depth, reach, and dump height define the machine envelope. A machine that cannot reach the trench or place spoil where the site requires adds handling time. Check these values against the actual job geometry, not against a similar machine from another shortlist.

Hydraulic Performance Numbers

Auxiliary flow and pressure determine whether a breaker, auger, or thumb runs at full speed and force. If the attachment needs more flow than the machine can deliver, the tool cycles slowly and heat load rises. That condition shortens tool life even when the excavator itself is new.

Dimensional and Transport Numbers

Tail swing radius and width decide access between buildings, gates, and trailers. Operating weight determines trailer size, ground pressure, and lifting stability. These figures matter before delivery, not after.

Which Specification Numbers Should You Check First?

Start with the constraints that cannot be changed on site: access width, trailer rating, and the attachment hydraulic requirement. The table below is the short form I use when a buyer sends a specification sheet for review.

规格参数	What it constrains	Why it matters
操作重量	Trailer size, ground pressure, lifting stability	Determines transport and site access
最大挖掘深度	Trench and footing reach	Confirms the machine can complete the primary cut
辅助液压流量	Breaker, auger, thumb performance	Prevents underpowered attachment operation
Tail swing radius	Working between structures	Reduces collision risk in confined sites
Transport width	Gate, path, and trailer clearance	Confirms the machine can reach the work area
Bucket breakout force	Bucket penetration and lifting capacity	Confirms the machine can dig the expected material

Procurement teams can use this list to reject a machine in minutes instead of reading every line. If two machines pass all six rows, then compare engine power, fuel burn, and service access. That second comparison only becomes relevant after the physical and hydraulic requirements pass.

How Do Operating Weight and Digging Depth Work Together?

Operating weight and digging depth often appear together on a shortlist because buyers want a small machine that still reaches the required cut. Weight mainly affects stability, ground pressure, and trailer selection. Digging depth mainly affects whether the bucket can complete the trench without repositioning. A narrow transport width can force a lighter structure, which may reduce lift capacity at full reach. In machine shortlists for constrained building plots, I have seen operating weight treated as the final number when it should be the first. The better sequence is to confirm the required depth, then find the lightest machine that still holds lift capacity and auxiliary flow. 泰德’s mini excavator line spans several weight classes from TD10 to TD40U, which makes that sequence easier to run without switching suppliers.

Site condition matters because two machines with the same digging depth can have different ground pressure depending on track shoe width and operating weight. That difference changes how early a machine can enter a wet site or cross a finished lawn.

Why Do Hydraulic Flow and Auxiliary Circuit Specs Matter?

Attachment work reverses the usual specification priority. Engine power becomes secondary to auxiliary hydraulic flow, pressure, and return line capacity. A breaker does not care how many kilowatts the engine produces unless the pump can deliver the required flow at the stated pressure. If the flow is under the attachment minimum, the tool runs slow and heat builds in the circuit. If the flow is well above the attachment rating, the tool may need a flow control valve or risk damage. The best check is to write down the attachment flow and pressure requirement, then compare the exact values to the auxiliary circuit. Rated power never substitutes for that comparison.

If your next job involves a breaker, auger, or thumb, confirm the attachment hydraulic requirement before ordering the machine. A model that meets all trenching figures can still fall short on auxiliary flow. Send the attachment data sheet or model number to [email protected] and we can check it against the relevant 泰德 mini excavator before you finalize the specification.

What Should You Confirm Before Finalizing a Mini Excavator Specification Sheet?

Most specification problems show up after delivery, and they usually involve site access or attachment flow. The buyer confirms the digging depth, then discovers the trailer cannot carry the operating weight or the gate cannot clear the tail swing radius. The fix is simple when the right questions are asked before the order. Write down the access width, trailer capacity, and attachment flow requirement. Put those three values together with the target delivery period and destination country. Send them to [email protected] or call +86 591 2806 8999, and we will check the specification set against the applicable machine before you commit. This step catches the expensive mismatches while the decision is still cheap to change.

What Questions Do Buyers Ask About Mini Excavator Specifications?

Should I compare every specification line between machines?

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.